Skip to main content
Version: v4

Traktor Pro related Settings

info

Note: These settings are only available when NUO-STEMS Mode is set to "Native Traktor Pro 4" or "Traktor Pro 4 Legacy / Export Mode". They are hidden when in other modes.

Compression of .stem.m4a​

Select the compression format for stem files:

  • Recommended for most use cases
  • Provides high quality with constant bitrate
  • Higher than Traktor's own stems: Traktor Pro 4 creates stems in AAC at 256 kbps on macOS and 192 kbps on Windows

AAC 256 kbps (VBR)​

  • Good quality with smaller file size
  • On Windows without iTunes, it's shown as AAC 256 kbps (CBR): the built-in encoder uses a constant bitrate (see below)
  • Default in Native Instruments "Stem Creator" software

AAC on Windows: install iTunes for smaller AAC 256 files​

On macOS, NUO-STEMS always encodes AAC with Apple's encoder. On Windows, Apple's encoder comes with iTunes:

  • When iTunes is detected and its encoder is usable, both AAC options use Apple's encoder. AAC 256 uses variable bitrate: files are smaller and the quality slightly higher. AAC 320 keeps the full frequency range, up to 22 kHz.
  • When Apple's encoder is unavailable, NUO-STEMS uses its built-in encoder, fdkaac (based on the Fraunhofer FDK AAC library). AAC 256 is encoded at a constant 256 kbps. AAC 320 keeps frequencies up to 20 kHz, above what most people can hear.

If checking or encoding with Apple's encoder fails, NUO-STEMS automatically falls back to the built-in encoder, even if iTunes is installed.

Settings shows whether iTunes was found. Install iTunes with Apple's installer, then click Check again. The Microsoft Store version of iTunes can't be used.

ALAC (Lossless)​

  • Not recommended. See warnings below.
  • Lossless compression, preserves original quality in 16-bit 44100Hz
  • Results in larger file sizes
warning

ALAC encoded .stem.m4a seem to currently work only on macOS Traktor Pro (as of October 2025).

warning

Some ALAC encoded .stem.m4a files show corruption errors in Traktor Pro 4 at the end of the track. It doesn't affect the playback and seems to not crash Traktor. But I would advice to stay away from ALAC encoding for now.

STEMS Colors​

Customize the colors used for your STEMS in Traktor and on supported controllers.

Changes apply to newly converted files only.

tip

Not all controllers support the full gamut of colors. If a selected color does not appear as expected, try experimenting with different values or use a preset optimized for your gear.

info

To update colors for previously converted TP4 native stems, use Change TP4 STEMS colors for previously converted TP4 native stems.

Auto-start Processing When Collection Loaded​

When enabled, NUO-STEMS will automatically start processing tracks in the queue as soon as the Traktor collection is successfully loaded.

info

Keep in mind that "Auto-start processing" from Advanced tab in settings takes precedence over this setting.

Auto-start Processing When Adding Traktor Tracks​

When enabled, NUO-STEMS will automatically start processing tracks in the queue as soon as Traktor tracks are added to the queue.

Processing while Traktor is running (experimental)​

danger

Leave this off unless you have a specific reason to use it. It is meant for advanced users who accept doing a manual repair afterwards.

Setting name: Allow Traktor Pro 4 Native processing while Traktor is running. It is available only in Native Traktor Pro 4 mode and is off by default.

Normally NUO-STEMS pauses Traktor tracks while Traktor Pro 4 is open, because Traktor overwrites collection.nml when it quits. With this setting enabled, NUO-STEMS keeps generating STEMS while Traktor is open:

  • It uses the collection Traktor last saved, so tracks imported into Traktor since then may not appear yet.
  • STEMS files are created as usual, but NUO-STEMS does not save collection.nml until Traktor is closed. Traktor will not show the new STEMS yet.
  • When Traktor closes, NUO-STEMS reloads the collection Traktor saved.

To link the new STEMS:

  1. Close Traktor completely and leave NUO-STEMS open.
  2. On the Traktor Pro 4 page, wait for the collection to load.
  3. Click Needs Repair next to the collection name and apply the collection repair.
  4. Reopen Traktor.

While Traktor is open, changing STEMS colors, migrating .stem.m4a files, and collection repair are unavailable.

warning
  • Existing STEMS files can be overwritten while Traktor is using them. Avoid generating STEMS for the same track in NUO-STEMS and Traktor at the same time.
  • Generating STEMS can affect Traktor's playback performance.
  • Collection text tags added by NUO-STEMS while Traktor is open are not saved.